I checked out your Jayco 2016 Camper model 12UD and I think you'd really like the Jack-It 2 bike rack part # LC429756. This attaches to your trailer jack mount and gives you a 2 bike rack that is held above the propane tanks.
Then if you ever wanted to mount the rack in a hitch you could use the # LC723359 to convert it to a hitch rack. view full answer...
We have the exact cover you are seeking for your 12 foot 2008 Jayco Jay Series pop-up camper.
- Classic Accessories Deluxe PolyPro III Heavy-Duty Pop-Up Camper Cover # CA80040
This is a great cover with the air vents you mentioned and will keep your camper safe from the elements with its triple layered top and snug fit. view full answer...
Unfortunately you can't mix and match hubs and drums so you'll have to replace both. You'll need to first find your bearing combination. To do so you'll need to remove the hub and look at the number stamped into the face of the bearing. If that number is worn to the point that you cannot read it you will need to use digital calipers like the # PTW80157 to precisely measure you spindles according to the included diagram.
Once you have the bearing measurements please reply back and I can... view full answer...
For your 2006 Jayco 1206 I recommend the Kenda Karrier ST185/80R13 part # AM10208. For a compatible wheel I recommend going with the # AM20232 which will work perfectly assuming you have the common 5 on 4-1/2" bolt pattern.
If you find you have a different bolt pattern just let me know. view full answer...
Thanks for the picture of your axle as I can see a brake mounting flange which means brakes can be added. Now what we have to do next is determine you axle capacity so we can pick out the correct hub/drums and then from there the correct brake assemblies.
Also, what trailer wiring does your Sienna have? You'll need a brake controller to control the trailer's brakes. view full answer...
The largest trailer tire for a 14 inch rim is the size 215/75-14 which is only .4 inches taller overall than the other size that this size wheel will have of 205/75-14 which is what you probably have so it would easily fit without issue.
For that size we have the Kenda Karrier part # AM10229. it has a weight capacity of 1,870 max load at 50 psi, a speed rating of 81 mph and a 1-year warranty. Check out the review video I attached for more info as well. view full answer...
The Progressive Dynamics Inteli-Power RV Converter and Battery Charger # PD9160A you referenced would be a solid choice for charging your two batteries. This can provide up to 60 amps of charging power that is multi-staged and has built in safety features that prevent overcharging and overheating. view full answer...
Great News, The ST145/R12 tire size with load range E like # AM10140 can be paired with an aluminum wheel like part # AM22318HWT. These do not come mounted. You would need to have them mounted at a local shop upon arrival. The # AM22318HWT is a 4 on 4. If you need a 5-bolt wheel, the # LH45FR would work instead of the # AM22318HWT.
We normally do not recommend going down in load ranges from what the manufacturer put on the trailer but if the tire is properly rated for the weight of... view full answer...
The Global Link RV Entry Door Locking Latch Kit # 295-000019 will fit your door if the cutout hole is 2-1/2" wide x 3-1/2" tall to 3" wide x 4" tall. Manufacturers do not list the door handles they use so the only way to replace them is to have the brand and serial number of the door handle to look up the exact size or just take it off and measuring the cutout hole to find a compatible fit. view full answer...
The overall outside width dimension of the Dexter DX7.5 -N-Go Brake Actuator - Drum Brakes - 2inch Ball - Zinc Plated - 7,500 lbs Item # 099-175-00 that you referenced is 3-1/2 inches. It normally fits onto a 3 inch wide frame channel and has a metal thickness of 1/4 inch. view full answer...
Thanks for the pictures! You are going to want the Titan Brake Actuator with Manual Lockout item # T63FR. This replacement brake actuator will fit in place of your Atwood 82543 and slide right into your trailer's coupler.
The Titan also has a 3" bolt pattern, a 2" ball coupler, and manual lockout similar to your Atwood. This actuator has a slightly higher capacity of 7,500 lbs. view full answer...
When it comes to installing The Trailer Coupler Lock - Gorilla Guard for 2 inch Couplers # 63228 will work for your 2006 Jayco J-Series Pop-Up trailer if the coupler width (including the lip) cannot exceed 3-3/16 inches. Also the height of the coupler lip cannot be greater than 5/16 inches.
I attached a review video link below. view full answer...
Since your drums are designed for 10" brakes, and it looks like you've got a 4400-lbs Dexter axle on your 2006 Jayco 12HW the replacement brakes you're looking for are the Dexter Electric Brake Kit for 4.4K Axles Manufactured Before May 2009 - 10" - Left/Right Hand # 23-454-455. view full answer...
You sure can!
The 145/R12 tire you have on your tent trailer measures in at 5.7" wide and 21.3" tall where the 5.30-12 tire you mentioned measures 5.5" wide and 21.9" tall. Since they are so close in size that can be interchanged with zero fitment issues.
With that said we actually have the exact 145/R12 tire you are looking for, the Kenda Karrier S-Trail ST145/R12 Radial Trailer Tire - Load Range D # AM10130. This tire is not only the same size, but has the same load range D rating as... view full answer...
You would need to flip the axle on your 2011 Jayco 141J, there is no model with an adjustable axle. The Dexter Trailer Springs Over-Under Conversion Kit # K71-384-00 works for 2-3/8" diameter axles to move your trailer's leaf springs to the top of your axle. view full answer...
You would need to measure from the hub face to hub face and then from the spring mount centers to pick out the correct axle to fit your trailer. In order for the # 20440I-EZ-72 to work the distance between the spring seat centers would need to be 58 inches and from hub face to hub face would need to be 72 inches.
If you need something different let me know but I do not have a way to look up the specs of your Jayco. This specific axle can only be used on up to 12 inch diameter wheels. view full answer...
We have two different brackets for our dual cam compatible weight distributions systems:
-Strait-Line system with snap up brackets and chains with a separate dual cam system.
-Strait-Line system with Dual Cam II with brackets with an integrated dual cam system.
The snap up brackets (# RP21501) can still be purchased, or as the you suggested you can use the alternative chain hangers (# RP58305). Both of which are compatible with the dual cam HP (# RP26002). Both options require drill... view full answer...
We have the Furrion RV Tankless Water Heater # FR98SR which fits has an overall size of 19-3/16" deep x 12-5/8" tall x 12-13/16" wide and an access door size of 16-1/8" tall x 16-1/8" wide so it will be a perfect replacement for your discontinued Atwood GC6AA-10E. There isn't a direct replacement for what you have at this time. view full answer...
From online photos I've seen, the # RVST60 passenger side taillamp looks like the correct replacement, although I can't definitively confirm that because there isn't a good resource that tells us what particular lamp is used on which camper. The lamp measures 8-5/8 x 3-3/16, so it that's a match for yours, this would be a compatible lamp. For the driver's side, part # RVST61 is used. view full answer...
If you can believe it the Fogatti RV Tankless Water Heater - Gas - Automatic Pilot # LSB64FR is actually the largest water heater we offer.
The overall dimensions of the unit are 14-3/8" long x 15" wide x 15" tall which is closer to what you're needing but we aren't going to have anything that matches directly. What you could do is get some lumber from your local home improvement store and use it to fill the gap and give the new water heater something to mount to. view full answer...
Go To Results